Ends Today : Buy 2 Get 2 Free | Shop Now »

How to Setup SuperRack SoundGrid with DiGiCo SDx Consoles with Remote Control

Apr 15, 2024

Follow these instructions to setup a DiGiCo SD console & Waves SuperRack SoundGrid with ProLink console remote integration.

  • Let’s start with a list of all hardware, software and peripherals you will need to set this up:

    1. One DiGiCo SD console (Quantum users, please follow the instructions here) with a Waves I/O.
    2. Two computers, running either Windows or Mac that fully support SuperRack SoundGrid with:
      • SuperRack SoundGrid installed and licensed.
      • SoundGrid supported plugins.
    3. A USB Flash Drive for Waves licenses (optional).
    4. At least one SoundGrid Server to process plugins.
    5. A SoundGrid supported network switch.
    6. At least four compatible Ethernet cables at supported lengths (you should always have a few extras with you).
  • Install and Activate Waves SuperRack SoundGrid and Plugins on the host computer:

      1. First, make sure that your computer fully supports running SuperRack SoundGrid and your Waves plugin versions.
      2. Install and activate Waves licenses on your host computer:
        1. Download and install Waves Central
        2. Launch Waves Central and login to your Waves account
        3. On the ‘Install Products’ tab, Select SuperRack SoundGrid and your plugins and/or bundles.
        4. Click “Install”.
      1. In Waves Central, go to the ‘Licenses’ tab, and select ‘Not Activated’.
      2. Select the licenses for SuperRack SoundGrid and your plugins and/or bundles.
      3. On the right panel, select the Target Device for Licenses. Either the computer or a USB flash drive.
      4. Click on Activate.
    • If you have a Quantum console, click here for specific instructions.
    • Connect the following to the network switch:
    • DiGiCo SD Engine
    • Waves SD I/O
    • Host Computer
    • Server #1
    • Server #2 – for redundancy or additional processing power
    • More servers can be added.
    • Power everything up.
    • Go to Options > Console tab.
    • Under Enable External Waves click YES and make sure the NIC of the console is chosen as Waves network.
    • Select ProLink if not already selected. Select Legacy if running SuperRack V14.23 and below.
    • Power cycle the console.
    • Launch SuperRack SoundGrid on the host computer.
    • In the Setup tab, under Port, choose the host computer’s LAN port that is used for SoundGrid.
      When a valid SoundGrid Port is recognized, the link status will show “Up” and the speed should show 1GBps.
    • Assign the Waves SD I/O and server/s in the I/O, Devices, Hosts and Servers panels respectively.
    • In SuperRack’s Setup tab under Controllers, assign the ProLink Console Remote Control module.
    • Click on the gearbox to open the panel.
    • The network port will be assigned automatically (ProLink only).
    • Assign the console. The status should change to Connected.
    • * If using Legacy console remote, you need to select the network port manually. Select the same network port used for your SoundGrid network.
      A session load command will pass from the console to SuperRack. If there is no matching session in SuperRack’s integrated sessions folder, SuperRack will load an empty session.

      SuperRack SoundGrid Integrated session folder location:
      • Windows: C:\Users\Public\Waves Audio\SuperRack SoundGrid\Integrated Sessions
      • Mac: Mac HD > Users > Shared > Waves Audio > SuperRack SoundGrid SoundGrid > Integrated Sessions
  • Now that your devices are assigned, you can route audio to the racks manually or automatically. To route automatically, go to the menu at the top left corner and choose Auto-Route.

    • Choose which bank to route to, A or B.

    SuperRack will now patch racks to the card in fixed routing. 1-1, 2-2, 3-3, etc.

    If you require a different routing scheme, you can patch racks manually. Refer to the SuperRack manual for more information on routing.